Bienvenue sur notre site officiel!
chines   |   France  |   Russia   |   Spain   |   Portugal   |   Arab   |   English
Nouvelles de la société.

Diesel Forklift,Why does the diesel engine smoke?



First, emit blue smoke:

The reason for the emission of blue smoke is that excessive combustion of the engine oil is caused by combustion. The reasons and troubleshooting for this phenomenon are as follows:

(1) The oil pan is over-oiled and the oil is too much. It will splash into the cylinder wall with the high-speed crankshaft and break into the combustion chamber. The elimination method is to stop the machine for about 10 minutes, check the oil scale, and remove excess oil.

(2) The cylinder liner and piston ring assembly are seriously worn and the clearance is too large. As a result, a large amount of oil can be burned into the combustion chamber, accompanied by an increase in crankcase exhaust gas. The method of disposal is to replace worn parts in time.

(3) The piston ring is disabled. If the piston ring has insufficient elastic force, the carbon deposit is stuck in the ring groove, or the ring mouth is on the same straight line, or the oil ring is blocked by the oil return hole, which will cause the oil to enter the combustion chamber to burn and emit blue smoke. The method of disposal is to remove the piston ring, remove the carbon deposits, rearrange the buckles, and replace the components if necessary.

(4) The clearance between the valve and the conduit is too large. During the intake, the engine oil in the rocker arm enters the combustion chamber and burns. The method of treatment is to replace worn valves and conduits in a timely manner.

(5) The reason for the emission of blue smoke is that if the oil is too thin, the oil pressure is too high, and the engine is not running well, it will cause the oil to burn and emit blue smoke.

Second, exhaust smoke to black:

This phenomenon is caused by incomplete combustion of the fuel. When black smoke is emitted, the engine power is often reduced, the exhaust temperature is too high, and the water temperature is too high, which causes several pieces of engine wear and affects the engine life. The reasons and troubleshooting for this phenomenon are as follows:

(1) Insufficient intake or blockage of the intake pipe. In order to find out the cause, the following checks should be made: whether the air filter is blocked; whether the intake pipe is leaking; whether the turbocharger is damaged.

(2) improper adjustment of valve clearance. Poor contact of the valve seal ring. Valve clearance, valve spring and valve seal ring should be checked.

(3) The supply of each cylinder of the high pressure oil pump is uneven or too large. The result is unstable speed and intermittent black smoke, which should be adjusted to make it balanced or within the specified range.

(4) If the fuel injection is too late, the fuel injection advance angle should be adjusted.

(5) If the injector is not working properly or is damaged, it should be removed for inspection.

(6) The cylinder liner and piston ring assembly are seriously worn. When this happens, the piston ring is not tightly sealed, the air pressure in the cylinder is lowered, and the diesel engine cannot be fully burned to emit black smoke, and the engine power is drastically lowered. When the load is severe, the engine will automatically turn off. Wear parts should be replaced.

Third, the emission of yellow smoke:

In the initial stage of the start-up operation, yellow smoke is emitted at the medium-speed stage, and the phenomenon of yellow smoke emission gradually decreases or disappears after the temperature rises or the load increases. The performance is that the speed is easy to turn off, the body is shaken, and the intake pipe is “smothered”, the exhaust pipe is fired, the power is insufficient, and the starting is difficult. The reasons and troubleshooting methods for this phenomenon are as follows:

(1) The individual intake and exhaust valves are not closed tightly, or the valve springs are insufficiently elastic, the valve push rods are bent, and the intake and exhaust valves are ablated. The treatment method is: grinding the valve, removing the carbon deposits, and replacing the worn parts.

(2) The clearance between the camshaft journal and the seat hole is too large or the phase of the valve is out of alignment. Most of the valve ablation, the cylinder liner and the piston ring wear excessively. The treatment method is: adjust the clearance and replace the wear parts.

The WSM was established in jinjiang, near the world stone trade centre, in 2003, A gradual but constant development led the company to a world top position. A full and complete range of equipment covers any kind of requirements for block excavation and processing. Our high specialization allow us to offer unique and high tech products like the innovative block hander.

Retour >


maison À propos de nous Produits Notre équipe Nouvelles Nous contacter


Sous-station Copyright © Fujian Weisheng Machinery Development Co., Ltd. Nos produits comprennent divers équipements, machines et accessoires pour le traitement de carrières et de pierres naturelles, chariots diesel, chariots diesel, grues automatiques, chariots de manutention Chariot élévateur, grue diesel
Soutenu par   Chinatuiba

Fujian Weisheng Machinery Development Co., Ltd

Adresse: Zone de développement économique Anton, ville de Jinjiang, province du Fujian, Chine

+86 0595 85589798     Mobile:+86-13960411955